Vibro-Meter® Việt Nam | Đại Lý Phân Phối Vibro-Meter® Việt Nam

cuahangtudonghoa — 2019-08-09 11:53:49

Tăng Minh Phát là nhà cung cấp các thiết bị công nghiệp tại Việt Nam

Đại Lý Vibro-Meter® Việt Nam

Vibro-Meter® Việt Nam

Meggitt Sensing Systems Switzerland (MSS Switzerland) leads the market in sensing and monitoring solutions, specialising in smart engineering for extreme environments. Our 60+ years of sensor and system expertise means our solutions are trusted by original equipment manufacturers around the world.

MSS Switzerland was founded as Vibro-Meter® back in 1952. This became a Meggitt company in 1998 and in 2006 was integrated into the Meggitt Sensing Systems division.

Đại Lý Vibro-Meter® Việt Nam

Xem thêm sản phẩm Vibro Meter TẠI ĐÂY

The post Vibro-Meter® Việt Nam | Đại Lý Phân Phối Vibro-Meter® Việt Nam appeared first on cuahangtudonghoa.com.

AE119 housing expansion probe | Đầu dò AE 119 Vibro-Meter

cuahangtudonghoa — 2019-08-08 13:15:23

Công Ty TNHH TM và DV Tăng Minh Phát chuyên cung cấp các thiết bị hãng Vibro-Meter tại Việt Nam

Đầu dò AE 119 Vibro-Meter

High-quality, high-reliability housing expansion probe. For use in harsh industrial environments.

Features
Designed for the long-term measurement of housing expansion in extreme environments, such as gas turbines and steam turbines
50 or 100 mm measurement range
0 to 80 °C (32 to 176 °F) operating temperature, IP54 protection rating
Integrated electronics
Current loop output (4 to 20 mA) for signal transmission over long distances

SPECIFICATIONS
Electrical
Input power requirements
• Voltage : +20 to +32 VDC
• Current : 60 mA nominal at 24 VDC (70 mA max.)
• Max. load resistance : 500 Ω
Operating
Frequency response
• Electrical : 0 to 1000 Hz
• Mechanical : 0 to 5 Hz
Accuracy
• Linearity : <1% of FSD
• Resolution : <0.05‰ of FSD
• Reproducibility : <0.05‰ of FSD
Temperature drift
• On zero : <150 ppm/°C of FSD
• On sensitivity : <150 ppm/°C of FSD
Output signal
• Constant current signal : 4 to 20 mA
• Start position : Adjusted to 4 mA ±0.15 mA (rod fully inserted)
• End position : Adjusted to 20 mA ±0.3 mA (rod fully extracted)

Ordering number:

800-119-000-025-A1-B1

800-119-000-025-A2-B1

800-119-000-025-A1-B2

800-119-000-025-A2-B2

800-119-000-112-A1-B1

800-119-000-112-A1-B2

800-119-000-112-A2-B1

800-119-000-112-A2-B2

The post AE119 housing expansion probe | Đầu dò AE 119 Vibro-Meter appeared first on cuahangtudonghoa.com.

Pressure sensors (CP) Vibro-Meter | Cảm biến áp suất Vibro-Meter

cuahangtudonghoa — 2019-08-07 11:58:41

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

Piezoelectric pressure transducer CP 235 | Cảm biến đo áp suất CP 235

FEATURES 143-235-000-0
» From the Vibro-Meter® product line
» Acceleration compensated
» Designed for use in gas turbines
» Certified for use in potentially explosive atmospheres
» High reliability
» Wide temperature range: −55 to 520°C
» Frequency response: 2 to 10000 Hz
» High sensitivity: Min. 750 pC/bar
» Weight:
Transducer head: 50 g
Integral MI cable: 140g/m

Thông số kỹ thuật pressure transducer CP 235
Operating (at +23°C ±5°C)
Sensitivity (at 2 Hz) : 750 pC/bar (52 pC/psi) min.
Static pressure (on sensing head) : 0.1 to 20 bar
Dynamic measuring range (random) : 0.00005 to 5 bar nom.
Overload capacity (spikes) : Up to 100 bar (1450 psi)
(static + dynamic components)
Linearity : ≤±1% over dynamic measuring range

Ordering number

143-235-000-012

143-235-000-022

2. Pressure transducer CP216 | Đầu dò áp suất CP216

Đặc điểm đầu dò áp suất CP216
» From the Vibro-Meter® product line
» Extreme temperature capability: −70 to 520°C
» High-pressure capability: up to 350 bar
» Pressure sensitivity: 200 pC/bar
» Frequency range: 2 Hz to 15 kHz
» Internal case insulation
» Certified for use in potentially explosive atmospheres
Operating (At 23°C ±5°C, 73°F ±9°F)
Sensitivity (typical, at 2 Hz) : 200 pC/bar (13.8 pC / psi)
Dynamic measurement range (random) : 0.0005 bar to 250 bar (0.007 psi to 3626 psi)
Overload capacity (spikes) : Up to 350 bar (5076 psi) (static + dynamic components)
Linearity : < ±1% over dynamic measurement range
Acceleration sensitivity : ≤ 0.5 pC/g (0.0025 bar/g, 0.036 psi/g)
Resonant frequency : > 80 kHz
Frequency response : 2 to 15000 Hz ±5%.
The lower cutoff frequency is determined by the electronics used.
Capacitance (nominal)
• Pole to pole : 320 pF for transducer + 200 pF/m (61 pF/ft) of cable
• Pole to casing : 13 pF for transducer + 300 pF/m (91 pF/m) of cable
Internal insulation resistance : > 109 Ω. > 5x104 at 450°C (842°F).

Ordering number

143-216-000-011

143-216-000-021

143-216-000-031

143-216-000-041

143-216-000-051

143-216-000-111

143-216-000-121

143-216-000-131

143-216-000-141

143-216-000-151

143-216-000-161

3. Pressure transducer CP 103 | Đầu dò áp suất CP 103

Mô tả đầu dò áp suất CP 103
» From the Vibro-Meter® product line
» Extreme temperature capability −196 to +700°C
» High-pressure capability up to 250 bar
» For use in gas turbines
» Operational in primary circuit of PWR, APWR, BWR, ABWR, FBR and HTGR
» Proven reliability
» Meets NRC guide 1.20, IEEE 323-1974
» Certified for use in potentially explosive atmospheres
» Internal case insulation
» VC2 type crystal element

Thông số kỹ thuật đầu dò áp suất CP 103
Operating At +23°C ±5°C (+73°F ±41°F)
Sensitivity (at 2 Hz) : 232 pC/bar (16 pC/psi) ±5% typical
Dynamic measuring range (random) : 0.00004 to 20 bar nominal
Overload capacity (spikes) : Up to 250 bar
Linearity : ±1% over dynamic measuring range
Acceleration sensitivity : ≤0.05 pC/g (≤0.000 21 bar/g)
Resonant frequency : >50 kHz
Frequency response : 2 to 10000 Hz ±5% (the lower cut off frequency is determined by the electronics used)
Internal insulation resistance : Min. 109 Ω. 107 Ω at 300°C (+572°F)

Ordering information

143-103-000D502

143-103-000D602

143-103-000D702

143-103-000D901

The post Pressure sensors (CP) Vibro-Meter | Cảm biến áp suất Vibro-Meter appeared first on cuahangtudonghoa.com.

Vibration sensors Meggitt | Cảm biến rung Vibro-Meter

cuahangtudonghoa — 2019-08-06 17:07:07

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

Vibration sensors (CA, CE, CV, PV, SE and VE)

Velocity transducers CV213 | Cảm biến vận tốc CV213

MEGGITT SA

Ordering number : 110-213-000-012

Velocity transducers CV214 | Đầu dò vận tốc CV214

MEGGITT SA

Ordering number : 110-214-000-012

Piezoelectric accelerometer CA 134 | Gia tốc kế CA 134

Ordering number: 144-134-000-203

Piezoelectric accelerometer CE 134 | Cảm biến vận tốc CE 134

Ordering number:

444-134-000-405

444-134-000-605

444-134-000-705

444-134-000-715

Piezoelectric accelerometer CA 202 | Đầu dò vận tốc CA 202

Ordering number:

144-202-000-205

144-202-000-215

144-202-000-225

144-202-000-235

144-202-000-105

144-202-000-115

144-202-000-125

144-202-000-135

Piezoelectric accelerometer CA 280 | Đầu dò vận tốc CA 280

Ordering number:

144-280-000-015

144-280-000-115

144-280-000-125

Piezoelectric accelerometer CE281 | Cảm biến rung CE281

Ordering number:

444-281-000-012

444-281-000-112

444-281-000-212

Velocity transducer VE210 | Cảm biến rung VE210

Ordering number:

410 - 210 - 000 - 012 - A1 - B1 - C1

410 - 210 - 000 - 012 - A1 - B2 - C1

410 - 210 - 000 - 012 - A1 - B1 - C2

410 - 210 - 000 - 012 - A1 - B2 - C2

922-439-000-001

922-439-000-101

922-440-000-001

922-440-000-101

800-114-000-01

Piezoelectric Accelerometer CA 306 | Đầu dò vận tốc CA 306

Part Number (P/N)

144-306-000-011

144-306-000-111

144-306-000-121

144-306-000-131

144-306-000-141

144-306-000-311

144-306-000-321

144-306-000-331

144-306-000-341

Piezoelectric accelerometer CE311 | Cảm biến rung CE311

444-311-000-012

444-311-000-022

444-311-000-032

444-311-000-042

444-311-000-112

444-311-000-122

Piezoelectric accelerometer CA 901 | Cảm biến rung CA 901

Ordering Number

144-901-000-282

144-901-000-212

144-901-000-252

144-901-000-222

144-901-000-601

Piezoelectric accelerometer CE620 | Cảm biến rung CE620

Ordering number:

444 - 620 - 000 - 011 - A1 - B100

444 - 620 - 000 - 011 - A2 - B100

444 - 620 - 000 - 011 - A1 - B500

444 - 620 - 000 - 011 - A2 - B500

Piezoelectric accelerometer CE687 | Cảm biến rung CE687

Ordering number:

444 - 687 - 000 - 011 - A1 - B01

444 - 687 - 000 - 011 - A1 - B02

444 - 687 - 000 - 011 - A1 - B05

444 - 687 - 000 - 011 - A1 - B10

444 - 687 - 000 - 011 - A1 - B20

444 - 687 - 000 - 011 - A2 - B01

444 - 687 - 000 - 011 - A2 - B02

444 - 687 - 000 - 011 - A2 - B05

444 - 687 - 000 - 011 - A2 - B10

444 - 687 - 000 - 011 - A2 - B20

Piezoelectric accelerometer PV660 | Cảm biến rung PV660

Ordering number:

440 - 660 - 000 - 011

Piezoelectric accelerometer PV685 | Cảm biến rung PV685

Ordering number:

440 - 685 - 000 - 011 - A1 - B010

440 - 685 - 000 - 011 - A1 - B020

440 - 685 - 000 - 011 - A1 - B025

440 - 685 - 000 - 011 - A1 - B050

440 - 685 - 000 - 011 - A1 - B100

440 - 685 - 000 - 011 - A2 - B010

440 - 685 - 000 - 011 - A2 - B020

440 - 685 - 000 - 011 - A2 - B025

440 - 685 - 000 - 011 - A2 - B050

440 - 685 - 000 - 011 - A2 - B100

Piezoelectric accelerometer SE 120 | Cảm biến rung SE 120

Ordering number:

424-120-000-032

The post Vibration sensors Meggitt | Cảm biến rung Vibro-Meter appeared first on cuahangtudonghoa.com.

Velocity transducer CV213/CV214 | Đầu dò vận tốc CV213/CV214 Vibro-Meter

cuahangtudonghoa — 2019-08-06 10:27:21

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

Data Sheet CV213/CV214

Velocity transducer CV213/CV214

Đầu dò vận tốc CV213 và CV214 được thiết kế để đo độ rung tuyệt đối ở tần số thấp. Khi được sử dụng với cụm cáp, đầu dò có thể được kết nối trực tiếp với thiết bị điện tử giám sát mà không cần thêm bộ điều chỉnh tín hiệu và nguồn điện.
Hai thiết bị tương tự nhau về cấu trúc và hiệu năng, sự khác biệt duy nhất là CV213 dành cho các ứng dụng nhiệt độ cao, các môi trường hoạt động khắc nhiệt. Độ nhạy tốt và thiết kế chắc chắn làm cho các thiết bị này phù hợp với tất cả các loại máy móc công nghiệp tốc độ thấp. Vỏ nhôm anodised và đầu nối kín nước cho phép chúng chịu được môi trường ẩm ướt và ăn mòn.

SPECIFICATIONS

General

Operating principle : Moving coil and magnet
Power supply : No external power supply required
Signal transmission : 2-wire system insulated from casing, voltage-based output
Sensitivity

Directionality : Calibrated along the long axis of the transducer
Nominal sensitivity at 22°C (71.6°F) ±5°C : 20 mV/mm/s (508 mV/in/s) ±5% with signal of 100 Hz
Frequency range : 10 Hz to 1 kHz
Typical frequency response

10 Hz : −3 dB
30 to 400 Hz : ±0.5 dB
400 Hz to 1 kHz : ±1 dB.

Resonant frequency : 10 Hz ±1 Hz (nominal)
Transverse sensitivity : Max. ±10%
Output impedance : <700 Ω
Internal insulation resistance at 22°C (71.6°F) ±5°C

Case to (+) pole : >107 Ω
Case to (−) pole : >107 Ω
Machine to case : >107 Ω

Operating temperature

CV213 : −29 to 204°C (−20 to 400°F)
CV214 : −29 to 121°C (−20 to 250°F)

Storage temperature : −40 to 100°C (−40 to 212°F)
Protection rating (according to IEC 60529): IP64
Shock acceleration (according to IEC 60068-2-27) : 50 g peak (half-sine wave, 1 ms duration)

MEGGITT SA CV213

Velocity transducer CV213 | Cảm biến rung CV213

Order Code: 110-213-000-012

MEGGITT SA CV214

Velocity transducer CV214 | Cảm biến rung CV214

Order Code: 110-214-000-012

The post Velocity transducer CV213/CV214 | Đầu dò vận tốc CV213/CV214 Vibro-Meter appeared first on cuahangtudonghoa.com.

Relay card Vibro-Meter® | Đại Lý Phân Phối Vibro-Meter® tại Việt Nam

cuahangtudonghoa — 2019-08-02 14:24:26

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

Vibro-Meter® Việt Nam

Machinery protection card Type MPC4/MPC4SIL

200-510-SSS-1Hh

200-510-SSS-2Hh

200-510-SSS-3Hh

Input / output card IOC4T

200-560-000-1Hh

200-560-000-2Hh

VM600 analog monitoring card and input /output card

Type AMC8

200-550-0SS-1Hh

200-550-0SS-2Hh

Type IOC8T

200-580-000-1Hh

200-580-000-2Hh

Relay card RLC16

200-570-000-1Hh

200-570-000-2Hh

Intelligent relay card IRC4

620-005-0Ss-1Hh

601-001-CCC-VVv

VM600 modular CPU card and input /output card

Type CPUM

601-003-000-VVV\3\610-1CC-CCC (equivalent to a 200-595-0Ss-33h with a configuration)

601-003-000-VVV\3V\610-1CC-CCC (equivalent to a 200-595-0Ss-33hl with a configuration)

601-003-000-VVV\5\610-1CC-CCC (equivalent to a 200-595-0Ss-53h with a configuration)

Type IOCN

200-566-000-1Hh

200-566-000-1HhL

Extended vibration monitoring card pair XMV16 / XIO16T

Type XMV16: 600-003

Type XIO16T: 620-002-000-113

Type XMVS16: 600-016

Type XIO16T: 620-002-000-113

Type XMC16: 600-002

Type: 620-002-000-113

VM600 system rack ABE040 and ABE042

611-000-000/B0-C40S-D5-E0

611-000-000/B1-C40S-D5-E2

611-000-000/B2-C40S-D5-E3

611-000-000/B3-C40S-D5-E5

611-000-000/B0-C40C-D5-E6

611-000-000/B1-C40C-D5-E0

611-000-000/B2-C40C-D5-E2

611-000-000/B3-C40C-D5-E3

611-000-000/B0-C40I-D5-E5

611-000-000/B1-C40I-D5-E6

611-000-000/B2-C40I-D5-E0

611-000-000/B3-C40I-D5-E0

611-000-000/B0-C40V-D5-E0

611-000-000/B1-C40V-D5-E0

611-000-000/B2-C40V-D5-E0

611-000-000/B3-C40V-D5-E0

611-000-000/B0-C42S-D5-E0

611-000-000/B1-C42S-D5-E0

611-000-000/B2-C42S-D5-E0

611-000-000/B3-C42S-D5-E0

611-000-000/B0-C40S-D2-E0

611-000-000/B1-C40S-D2-E0

611-000-000/B2-C40S-D2-E0

611-000-000/B3-C40S-D2-E0

611-000-000/B0-C40C-D2-E0

611-000-000/B1-C40C-D2-E0

611-000-000/B2-C40C-D2-E0

611-000-000/B3-C40C-D2-E0

611-000-000/B0-C40I-D2-E0

611-000-000/B1-C40I-D2-E0

611-000-000/B2-C40I-D2-E0

611-000-000/B3-C40I-D2-E0

611-000-000/B0-C40V-D2-E0

611-000-000/B1-C40V-D2-E0

611-000-000/B2-C40V-D2-E0

200-582-500-021

200-582-500-022

200-582-200-021

200-582-200-022

200-582-600-021

200-582-600-022

VM600 rack power supply RPS6U

200-582-920-NHh

200-582-993-NHh

200-582-922-NHh

200-582-990-NHh

200-582-910-NHh

200-582-911-NHh

200-582-912-NHh

200-582-962-NHh

200-582-963-NHh

200-582-960-NHh

200-582-915-NHh

200-582-916-NHh

200-582-970-NHh

Auxiliary sensor power supply ASPS

200-582-810-0Hh

VM600 slimline rack ABE056

VM600SYS 611-000-000

611-000-000/B0-C56S-D2-H00-AA1-ZA1

611-000-000/B1-C56S-D2-H00-AA1-ZA1

611-000-000/B2-C56S-D2-H00-AA1-ZA1

611-000-000/B3-C56S-D2-H00-AA1-ZA1

611-000-000/B0-C56S-D5-H00-AA1-ZA1

611-000-000/B1-C56S-D5-H00-AA1-ZA1

611-000-000/B2-C56S-D5-H00-AA1-ZA1

611-000-000/B3-C56S-D5-H00-AA1-ZA1

611-000-000/B0-C56S-D2-H01-AA1-ZA1

611-000-000/B1-C56S-D2-H01-AA1-ZA1

611-000-000/B2-C56S-D2-H01-AA1-ZA1

611-000-000/B3-C56S-D2-H01-AA1-ZA1

Voltage-drop adaptor IOC 4T adaptor

200-560-900-021/

200-560-900-022/

Capacitive-coupling adaptor IOC 4T adaptor

200-560-910-021/

200-560-910-022/

The post Relay card Vibro-Meter® | Đại Lý Phân Phối Vibro-Meter® tại Việt Nam appeared first on cuahangtudonghoa.com.

Bộ nguồn 200-582-500-021 RPS6U - Vibro Meter Việt Nam | MEGGITT VIET NAM

cuahangtudonghoa — 2019-05-03 16:31:03

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

NEGGITT VIET NAM

Bộ nguồn 200-582-500-021

200-582-920-NHh
200-582-993-NHh
200-582-922-NHh
200-582-990-NHh
200-582-910-NHh
200-582-911-NHh
200-582-912-NHh
200-582-962-NHh
200-582-963-NHh
200-582-960-NHh
200-582-915-NHh
200-582-916-NHh
200-582-970-NHh

VM600 rack power supply

FEATURES
» From the Vibro-Meter® product line
» Power supply for VM600 system racks
» Input: AC-input and DC-input versions providing a wide input voltage range
» Output: +5 VDC and ±12 VDC
» Output over-voltage, short-circuit and overload protection
» Status indicators
» High-power, high-performance, high-efficiency
» Minimal derating within the operating temperature range

Drawing

Designation

Ordering number

Equivalent VM600SYS
order option code

(a)

One DC input with screw-terminal connector that
provides a common input to the RPS6U rack power supplies.

200-582-920-NHh

F200

(b)

Two DC inputs with screw-terminal connectors that
provide individual inputs to the RPS6U rack power supplies.

200-582-993-NHh

F930

(c)

One DC input with screw-terminal connector that
provides a common input to the RPS6U rack power supplies.
Also provides a special earth terminal (identified as M.A.L.T.).

200-582-922-NHh

F220

(d)

Two DC inputs with screw-terminal connectors
that provide a common input to the RPS6U rack power supplies.
Supports redundant external power-supply systems.

200-582-990-NHh

F900

(e)

One AC input (120 / 230 VAC) with mains socket and on/off switch
that provides a common input to the RPS6U rack power supplies.

200-582-910-NHh

F100

(f)

One AC input (120 / 230 VAC) with screw-terminal connector, on/off
switch and rear-panel fuses that provides a common input to the RPS6U rack power supplies.

200-582-911-NHh

F110

(g)

One AC input (120 / 230 VAC) with screw-terminal connector and rear- panel
fuses that provides a common input to the RPS6U rack power supplies.

200-582-912-NHh

F120

(h)

Two AC inputs (120 VAC only) with mains sockets and on/off switches
that provide a common input to the RPS6U rack power supplies. Supports redundant external power-supply systems.

200-582-962-NHh

F620

(i)

Two AC inputs (120 / 230 VAC) with mains sockets and on/off switches
that provide individual inputs to the RPS6U rack power supplies.

200-582-963-NHh

F630

(j)

Two AC inputs (230 VAC only) with mains sockets and on/off switches that provide a common
input to the RPS6U rack power supplies. Supports redundant external power-supply systems.

200-582-960-NHh

F600

(k)

Two AC inputs (120 / 230 VAC) with screw-terminal connectors, on/off switches
and rear-panel fuses that provide individual inputs to the RPS6U rack power supplies.

200-582-915-NHh

F150

(l)

Two AC inputs (120 / 230 VAC) with screw-terminal connectors and rear- panel
fuses that provide individual inputs to the RPS6U rack power supplies.

200-582-916-NHh

F160

(m)

One AC input (120 / 230 VAC) with mains socket and on/off switch and one DC input
with screw-terminal connector that provide individual inputs to the RPS6U rack power supplies.

200-582-970-NHh

F700

RPS6U rack power supply

Power supply

DC versions

AC version

Type

RPS 6U 24 DC

RPS 6U 48 DC

RPS 6U 72 DC

RPS 6U 110 DC

RPS 6U AC

Ordering number (1)

200-582-200-01h

200-582-300-01h

200-582-400-01h

200-582-600-01h

200-582-500-01h

Rated supply voltage

24 VDC

48 VDC

72 VDC

110 VDC

110 / 230 V (2) AC

Input voltage range
(Ui nom)

18 to 32 VDC

38.4 to 57.6 VDC

57.6 to 100 VDC

80 to 145 VDC

90 to 264 VAC
(auto-ranging)

Mains frequency variations

Not applicable

48 to 65 Hz

Efficiency

> 70%

> 75%

Marking

According to CE low voltage directive

LR111641
Level 3

200-582-200-01h
200-582-300-01h
200-582-400-01h
200-582-600-01h
200-582-500-01h

Website: https://catalogue.meggittsensing.com/vm600-rack-based-systems/rps6u.html

The post Bộ nguồn 200-582-500-021 RPS6U - Vibro Meter Việt Nam | MEGGITT VIET NAM appeared first on cuahangtudonghoa.com.

19\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\" Rack Types ABE 040 & ABE 042 Vibro-Meter® Việt Nam | MEGGITT VIET NAM

cuahangtudonghoa — 2019-05-03 15:51:00

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

ABE040 and ABE042

FEATURES

19" rack
Standard rack height of 6U
Robust aluminium construction
Modular concept allowing specific cards to be added for protection and condition monitoring
Cubicle or panel mounting
Backplane supporting VME bus as well as raw signal bus, tacho bus and open collector relay bus

SPECIFICATIONS
GENERAL
Construction : Extruded aluminium frame and solid aluminium structural parts. Top and bottom plastic guide strips for the plug-in cards.
Rack weight : 6.5 kg (without power supply units and cards).
Mains input : Racks are shipped with an RPS 6U power supply unit (2 units for systems with a redundant power supply). This unit has an AC or DC mains socket, mains cable of length 3 m and an RFI filter, if applicable.
Power supply : RPS 6U series (+5 V / ±12 V DC) to supply electronic processing cards, input/output cards and relay cards.
Backplane : Uses VME bus and dedicated bus for communication between cards. Unused slot positions must be covered with blank panels.
Galvanic separation : Galvanic separation units (GSI types), if required for accelerometer and proximity systems mounted in explosive atmospheres. These units cannot be supplied by the rack and require an external power supply. They must be mounted outside the rack in a
remote housing or in a cubicle.
ENVIRONMENTAL
According to IEC 68.2 recommendations
Temperature
• Operation : -25°C to +65°C
• Storage : -40°C to +85°C
Humidity : Max. 95% non-condensing
Vibration : 10 Hz to 55 Hz, 0.35 mm peak, 6 hours in each direction.
Shock : 15 g peak, 11 ms, half-sine pulse.

Ordering Number:

204-040-100-012

204-040-100-111

204-042-100-012

200-505-001-011

200-505-002-011

200-505-003-011

200-505-005-011

200-505-006-011

200-505-007-011

The post 19\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\" Rack Types ABE 040 & ABE 042 Vibro-Meter® Việt Nam | MEGGITT VIET NAM appeared first on cuahangtudonghoa.com.

620-005-0Ss-1Hh Relay Card Vibro Meter Việt Nam | MEGGITT VIET NAM

cuahangtudonghoa — 2019-05-03 15:21:18

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

Intelligent relay card IRC4
FEATURES
» From the Vibro-Meter® product line
» 8 relays can be combined as 4 DPDT or 8 SPDT
» Each relay is controlled by a specific logic equation, which can be a combination of AND, OR, NOT or VOTE (x between y) operators
» Each relay can be latched, with reset controlled by an external discrete signal interface (DSI) input or by a specific logic equation
» 64x raw bus lines, 16x OC bus lines and 6x external DSI inputs can be used as terms of the equations
» Each relay can be set to NE or NDE
» Delays can be set on each relay to ensure glitchfree operation
» 4 external DSI inputs can be used as general purpose inputs for the logic equations
» External AR and DB DSI inputs act as alarm (latch) reset and danger bypass
» Fully software configurable
» Non volatile configuration
» Screw terminal strip connectors (32 terminals)
» Ensures EMI protection for all inputs and outputs
» Live insertion / removal of cards (hot-swappable)

Relay characteristics

Relay names : RL1 to RL8
Type : PE014005
Contact arrangement : 1 x NO / NC contacts per relay (SPDT).
Relay contacts RL1-RL4 are available on the J1 connector and RL5-RL8 are available on J2 connector.
Nominal rated voltage : 250 VAC
Nominal rated current : 5 AAC
Maximum breaking capacity(without contact protection) : 1250 VA

Operate / release / bounce time : Typically 8 / 8 / 6 ms
Dielectric strength test voltages
• Between open contacts : 1000 VAC
• Between contact and coil : 4000 VAC
Mechanical life : 15 x 106 operations
Electrical life : >105 operations

DSI control signal inputs
Operating principle : Detection of an open or closed circuit on the input
Alarm reset (AR) : A closed contact between the AR and GND inputs resets latched alarms
Danger bypass (DB) : A closed contact between the DB and RET inputs allows the operator to inhibit the danger relay outputs
Discrete inputs
Number of inputs : 64x raw bus, 16x OC bus, 4x general purpose DSI inputs, including DB and AR
Input impedance : Raw bus and OC bus ≅ 1 MΩ.
DSI ≅ 10 kΩ.
Raw bus and OC bus threshold level : TTL
DSI threshold level : Ground (true) ≤3.0 V.
Open (false) ≥4.5 V (the IRC4 includes an internal pull-up to +12 V)

Relay card characteristics
Presentation : Eight 8 relay PCB
External connections : Two 16-contact screw terminal strip connectors (J1 and J2)
Mounting : Installs in the rear of a VM600 rack and connects to the rack’s backplane via a connector
Power supply
Power supply to IRC4 : +5 VDC / 0.50 A and +12 VDC / 0.01 A Environmental
Operating
• Temperature : −25 to +65°C (−13 to +149°F)
• Humidity : 0 to 90% non-condensing
Storage
• Temperature : −40 to +85°C (−40 to +185°F)
• Humidity : 0 to 90% non-condensing
Vibration and shock : See general rack specifications Physical
Height : 6U (262 mm, 10.3 in)
Width : 20 mm (0.8 in)
Depth : 125 mm (4.9 in)
Weight : 0.30 kg (0.66 lb)

Ordering number:

620-005-0Ss-1Hh

601-001-CCC-VVv

The post 620-005-0Ss-1Hh Relay Card Vibro Meter Việt Nam | MEGGITT VIET NAM appeared first on cuahangtudonghoa.com.

AMC8 and IOC8T Mạch bảo vệ Vibro Meter | MEGGITT VIET NAM

cuahangtudonghoa — 2019-05-03 15:00:40

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

FEATURES
» From the Vibro-Meter® product line
» Two cards providing 8 channels of temperature and process monitoring for VM600 systems
» 8 channels of software configurable functions: thermocouple (TC), resistance temperature detector (RTD), current and voltage inputs
» Analog signal inputs in 0 to 25 mA and 0 to 10 V range on any channel
» Cold-junction compensation (CJC) sensor processing on two selectable channels
» Current outputs (optionally, voltage outputs)
» Four relay outputs attributable to alarm signals under software control
» Control outputs to RLC16 relay cards in a VM600 rack
» Front panel LEDs indicate status and alarms
» Live insertion and removal of cards
» Available in ‘standard’ and ‘separate circuits’ versions

Sensor inputs
Thermocouple (TC) processing : Accepted TC types and temperature ranges:
• Type E (NiCr-CuNi): −270 to +1000°C (−454 to +1832°F).
• Type J (Fe-CuNi): −210 to +760°C (−346 to +1400°F), API 670 standard.
• Type K (NiCr-NiAl): −270 to +1372°C (−454 to +2501°F).
• Type T (Cu-CuNi): −270 to +400°C (−454 to +752°F).
• User-defined (user entry of linearising polynomial functions). Accuracy: 0.3°C (0.54°F) or 0.3% of measuring range. Resolution: 0.1°C (0.18°F).
Resistance temperature detector (RTD) processing
: Accepted RTD types and temperature ranges:
• Pt100, 100 Ω at 0°C, 3-wire and 4-wire platinum RTD (alpha = 0.00385): −200 to +850°C (−328 to +1562°F), API 670 standard.
• Pt100, 100 Ω at 0°C, 3-wire and 4-wire platinum RTD
(alpha = 0.00392): −200 to +700°C (−392 to +1292°F).
• Ni, 120 Ω, 3-wire and 4-wire nickel RTD: −80 to +260°C
(−112 to +500°F).
• Cu10, 10 Ω at 25°C, 3-wire and 4-wire copper RTD: −100 to +260°C
(−148 to +500°F).
• User-defined (user entry of linearising polynomial functions).
Accuracy: 0.3°C (0.54°F) or 0.3% of measuring range, except for Cu10
(1°C (1.8°F) or 1% of measuring range).
Resolution: 0.1°C (0.18°F).
Accepted RTD wiring schemes: 2-, 3-, and 4-wire for any RTD type. DC current (process input) processing • Total range 0 to 25 mA.
• Measuring resistor 50 Ω.
• Fuse-protected with 50 mA self-resetting fuse. Resistance seen from
input: the sum of fuse and measuring resistor resistance is maximum
100 Ω, typically 55 Ω.
• Positive polarity input only.
• Accuracy: 0.5% of total range, that is, 125 µA. DC voltage (process input) processing • Total range 0 to 10 V.
• Input resistance 100 kΩ.
• Positive polarity input only.
• Accuracy: 0.5% of total range, that is, 50 mV. Cold-junction compensation (CJC) processing
• Uses any type of temperature sensor.
• External compensation for accuracy, that is, no on-board temperature sensor.
• Results can be sent to any other AMC8/IOC8T card pairs in the same VM600 rack.

Discrete signal interface (DSI) inputs
Control signal
• Alarm reset (AR) : A closed contact between the DSI AR and RET inputs resets the alarms latched by the card pair
• Danger bypass (DB) : A closed contact between the DSI DB and RET inputs inhibits (bypasses) the danger relay outputs
Operating principle : Detection of an open circuit or a closed circuit on the input

Ordering number:

200-550-0SS-1Hh

200-550-0SS-2Hh

200-580-000-1Hh

200-580-000-2Hh

Physical
AMC8 card
• Height : 6U (262 mm, 10.3 in)
• Width : 20 mm (0.8 in)
• Depth : 187 mm (7.4 in)
• Weight : 0.4 kg (0.88 lb) approx.
IOC8T card
• Height : 6U (262 mm, 10.3 in)
• Width : 20 mm (0.8 in)
• Depth : 125 mm (4.9 in)
• Weight : 0.25 kg (0.55 lb) approx

Data sheet

The post AMC8 and IOC8T Mạch bảo vệ Vibro Meter | MEGGITT VIET NAM appeared first on cuahangtudonghoa.com.

CPUM and IOCN Bảng Mạch Vibro Meter | MEGGITT VIET NAM

cuahangtudonghoa — 2019-05-03 14:08:27

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

VM600 modular CPU card and input /output card
FEATURES
» From the Vibro-Meter® product line
» ‘One-Shot’ configuration of VM600 cards using a direct Ethernet or RS-232 serial connection from an external computer, such as a laptop, notebook or industrial PC, running the VM600 MPSx software
» Common alarm reset for machinery protection cards (MPC4 and AMC8) in a VM600 rack
» Front-panel display for visualisation of monitored outputs and alarm limits
» VM600 MPS rack (CPUM) security
» Fieldbus communications interfaces with support for industry standard protocols: Modbus and PROFINET
» Redundant Modbus communications can be configured for improved availability
» Two Ethernet connections and up to three serial connections (RS-232/RS-422/RS-485) can be accommodated simultaneously.

APPLICATIONS
» System controller for a VM600 rack
» Communications gateway between a VM600 rack and third-party systems, such as a DCS or PLC
» Machinery protection, condition monitoring and/or combustion monitoring

CPUM card
CPU module
Module type : PFM-541I or equivalent
Processor type : AMD Geode™ LX800
Processor speed : 500 MHz
Memory : 256 MB DRAM
Power supply to card (input) (taken from VM600 rack power supply) : 5 VDC, <1.8 A
Operating system : QNX
Communications ports (connections)
• Primary Ethernet : Network interface: 10/100BASE-TX.
Data transfer rate: Up to 100 Mbps.
Function: VM600 rack configuration and communications using the
VM600 MPSx software, and Modbus TCP and/or PROFINET.
Connector: ‘NET’ (CPUM card) or ‘1’ (IOCN card).
• Secondary Ethernet (requires the IOCN card)
: Network interface: 10/100BASE-TX.
Data transfer rate: Up to 100 Mbps.
Function: Redundant Modbus TCP communications.
Connector: ‘2’ (IOCN card).
• Primary serial : Network interface: RS-232.
Data transfer rate: Up to 115.2 kBaud.
Function: VM600 rack configuration and communications using the
VM600 MPSx software.
Connector: ‘RS232’ (CPUM card).
• Secondary serial (requires the IOCN card) : Network interface: RS-232 or RS-485.
Data transfer rate: Up to 115.2 kBaud.
Function: Modbus RTU communications.
Connector: ‘RS’ (IOCN card).
Note: The CPU module is fitted to all versions of the CPUM card. Serial communications module
Module type : AIM104-COM4 or equivalent
Power supply to modules (input) (taken from VM600 rack power supply) : 5 VDC, <220 mA
Isolation : >100 VDC
Communications ports (connections)
• Additional serial : Network interface: Two isolated RS-422 and/or RS-485.
Data transfer rate: Up to 115.2 kBaud.
Function: Modbus RTU communications.
Connectors: Two ‘A’ and two ‘B’ (IOCN card)

Ordering number:

601-003-000-VVV\3\610-1CC-CCC or 200-595-0Ss-33h

601-003-000-VVV\3V\610-1CC-CCC or 200-595-0Ss-33hl

601-003-000-VVV\5\610-1CC-CCC or 200-595-0Ss-53h

IOCN card
Connectors
RS : 6P6C (RJ11/RJ25), female. Used for the secondary serial connection.
A : Two 6P6C (RJ11/RJ25), female. Used for additional serial connections (requires the optional serial communications module).
B : Two 6P6C (RJ11/RJ25), female. Used for additional serial connections (requires the optional serial communications module).
1 : 8P8C (RJ45), female. Can be used for the primary Ethernet connection (instead of the ‘NET’ connector).
2 : 8P8C (RJ45), female. Used for the secondary Ethernet connection.

Electrical
Supply voltage : 5 VDC ±5%
Power consumption
• CPUM : <10 W
• IOCN : <2 W
RS-485 isolation : 500 VDC
Environmental
Temperature
• Operating : −20 to 65°C (−4 to 149°F)
• Storage : −25 to 80°C (−13 to 176°F)
Humidity : 0 to 90% relative humidity, non-condensing
Approvals
Conformity : CE marking, European Union (EU) declaration of conformity.
EAC marking, Eurasian Customs Union (EACU) certificate/declaration
of conformity.
Electromagnetic compatibility : TR CU 020/2011
Electrical safety : TR CU 004/2011
Environmental management : RoHS compliant
Russian federal agency for technical
regulation and metrology (Rosstandart) : Pattern approval certificate CH.C.28.004.A N° 60224, dated 11.11.2015

Ordering number:

200-566-000-1Hh

200-566-000-1HhL

Physical
CPUM
• Height : 6U (262 mm, 10.3 in)
• Width : 40 mm (1.6 in)
• Depth : 187 mm (7.4 in)
• Weight : 0.40 kg (0.88 lb) approx.
IOCN
• Height : 6U (262 mm, 10.3 in)
• Width : 20 mm (0.8 in)
• Depth : 125 mm (4.9 in)
• Weight : 0.25 kg ( 0.55lb) approx.

The post CPUM and IOCN Bảng Mạch Vibro Meter | MEGGITT VIET NAM appeared first on cuahangtudonghoa.com.

Bo Mạch VM600 MPC4 Vibro-Meter | Vibro-Meter® Meggitt

cuahangtudonghoa — 2019-05-03 13:45:09

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

MPC4 machinery protection card

200-510-SSS-1Hh

FEATURES
» From the Vibro-Meter® product line
» Continuously online machinery protection card
» Real-time measurement and monitoring using state-of-the-art DSP techniques
» 4 dynamic signal inputs and 2 tachometer (speed) inputs, all individually programmable
» Programmable broad-band and narrow-band filters
» Simultaneous amplitude and phase monitoring in order tracking mode
» Programmable Alert, Danger and OK set points
» Adaptive Alert and Danger levels
» Front panel BNC connectors for easy analysis of raw signals
» 7 front panel LEDs show status and alarms
» Integrated power supply for many Vibro-Meter front-ends, including ICP accelerometers and proximity systems
» Live insertion and removal of cards
» Available in ‘standard’, ‘separate circuits’ and ‘safety’ (SIL) versions

Ordering number:

200-510-SSS-2Hh

DESCRIPTION
MPC4 card
The MPC4 machinery protection card is the central element in the VM600 series machinery protection system (MPS), from Meggitt Sensing Systems’ Vibro-Meter® product line. This very versatile card is capable of measuring and monitoring up to four dynamic signal inputs and up to two speed inputs simultaneously.
The dynamic signal inputs are fully programmable and can accept signals representing acceleration, velocity and displacement (proximity), among others. On-board multi-channel processing allows measurement of various physical parameters, including relative and absolute vibration, Smax, eccentricity, thrust position, absolute and differential housing expansion, displacement and dynamic
pressure.
Digital processing includes digital filtering, integration or differentiation (if required), rectification (RMS, mean value, true peak or true peak-to-peak), order tracking (amplitude and phase) and measurement of the transducer-target gap.
The speed (tachometer) inputs accept signals from a variety of speed sensors, including systems based on proximity probes, magnetic pulse pick-up sensors or providing TTL signals. Fractional tacho ratios are also supported.
The calibration may be expressed in metric or imperial units. Alert and Danger set points are fully programmable, as are alarm time delay, hysteresis and latching. The Alert and Danger levels can be adapted as a function of the speed or any external information.
A digital output is available internally (on the corresponding IOC4T card) for each alarm level.
These alarm signals may be routed on a bus within the VM600 rack to drive relays on optional relay cards (such as the IRC4 and RLC16). The processed dynamic (vibration) signals and speed signals are available at the rear of the rack (on the front panel of the IOC4T) as analog output signals. Voltage-based (0 to 10 V) and current-based
(4 to 20 mA) signals are provided.
The MPC4 performs a self-test and diagnostic routine on power-up. In addition, the card’s built-in “OK System” continuously monitors the level of signals provided by the sensors and indicates any problem due to a broken transmission line, faulty transducer or conditioner.
An LED indicator on the MPC4 front panel indicates whether a processing or hardware error has occurred. Six additional LEDs (one per input channel) indicate whether the OK System has detected a fault and whether an alarm has occurred on the channel. The MPC4 card is available in three versions: a ‘standard’ version, a ‘separate circuits’ version and a ‘safety’ (SIL) version, all of which function as a card pair using an IOC4T input/output card
‘Standard’ and ‘safety’ (SIL) versions of the MPC4 Both the ‘standard’ version and the ‘safety’ (SIL) version of the MPC4 card are certified to IEC 61508 and ISO 13849.
The ‘standard’ MPC4 card is the original version, intended for safety systems using a VM600 rack with a limited range of cards, that is, ‘standard’ MPC4 / IOC4T card pairs and RLC16 relay cards. It has a VME-compatible slave interface and is fully software configurable via RS-232 (on the front panel of the card) or VME.
The ‘safety’ MPC4 card, also known as the MPC4 SIL, was developed to permit a wider range of installation options. Specifically, VM600 racks that also contain condition monitoring cards (such as the CMC16 and XMx16) and relay cards (such as the IRC4 and RLC16). To safety certify these configurations, it was necessary to ensure that the
‘safety’ MPC4 is isolated from the other cards in a VM600 rack, so that there is no possibility of its configuration being inadvertently modified.
Therefore, the ‘safety’ (SIL) version of the MPC4 does not include a VME-compatible slave interface, nor does it provide all of the signal processing capabilities of the ‘standard’ MPC4 card (see Specifications – ‘standard’ and ‘separate circuits’ MPC4 cards only on
page 6). Segregation of MPS and CMS
The VM600 rack, machinery protection cards, condition monitoring cards and associated software are designed for compliance with the machinery protection system (MPS) and condition monitoring system (CMS) “segregation” requirements of the API 670 standard, which ensures that the functionality of the MPS does not depend on and is not compromised in any way by the operation of the CMS.

200-510-SSS-3Hh

So although machinery protection cards and condition monitoring cards can easily share sensor signals from measurement chains, MPC4/IOC4T card pairs do not share any communication buses with XMx16/XIO16T condition monitoring card pairs in a VM600 rack, and MPC4/IOC4T card pairs are configured and operated using the VM600 MPSx software (while XMx16/ XIO16T card pairs are configured and operated using the VibroSight® software).

Applications information The MPC4 cards are highly suitable for machinery protection in a wide range of industrial applications. For further information on the use of MPC4 cards, refer to the VM600 Functional Safety Manual MAVM600-FS/E. For specific applications, contact your nearest Meggitt Sensing Systems representative.

SPECIFICATIONS – ALL MPC4 CARDS
Dynamic signal inputs
Number of inputs : 4 per MPC4 card
DC range : 0 to +20 V or 0 to −20 V
AC range : ±10 V (maximum)
Common mode voltage range : −50 to +50 V
CMRR : >60 dB at 50 Hz
Crosstalk : −72 dB
Input impedance : 200 kΩ
Current input range
• DC signals : 0 to 25 mA
• AC signals : ±8 mA (maximum)
Analog AC frequency band (without integration) : 0.1 Hz to 10 kHz
Analog AC frequency band (with integration) : 2.5 Hz to 10 kHz
Analog frequency band for throughput to other cards and buffered AC outputs : DC to 60 kHz (−3 dB)
Current measuring resistor : 324.5 Ω
Processing options
Broad-band
Filtering options : High-pass, low-pass or band-pass
LP/HP ratio in pass band : 500 (maximum)
Ripple : ±0.3 dB
Slope : 6 to 60 dB/octave (software configurable)
Attenuation outside pass band : >50 dB
Amplitude accuracy : ±1% of full-scale
Linearity error : <±1%
Equivalent input noise (without integration) : <200 µV RMS

Narrow-band (tracking)
The ‘standard’ and ‘separate circuits’ versions of the MPC4 card support narrow-band tracking (see Specifications –
‘standard’ and ‘separate circuits’ MPC4 cards only on page 6).
The ‘safety’ MPC4 card does not support narrow-band tracking.
Relative shaft vibration
Frequency band
• Vibration : 0.1 Hz to 10 kHz
• Gap/position : DC to 1 Hz
Amplitude accuracy
• Vibration : ±1.2% of full-scale
• Gap/position : ±1% of full-scale
• Linearity error : <±1%
Initial gap/offset compensation : Available
Buffered (raw) dynamic signal outputs
These signals are available on the MPC4 card’s BNC outputs and the IOC4T card’s raw outputs.
Frequency range : DC to 10 kHz (−0.1 dB or 1%).
DC to 60 kHz (−3 dB).
Admissible load on output : >50 kΩ
Amplitude error : <2%
Phase error : <5° (DC to 10 kHz)
Transfer ratio
• Voltage input : 1 V/V
• Current input : 0.3245 V/mA

Thông tin chi tiết: Catalog

200-510-071-113

The post Bo Mạch VM600 MPC4 Vibro-Meter | Vibro-Meter® Meggitt appeared first on cuahangtudonghoa.com.

VM600 RLC16 relay card Vibro-Meter Việt Nam | Vibro-Meter® Meggitt Việt Nam

cuahangtudonghoa — 2019-05-03 09:11:25

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

VM600 RLC16 relay card Vibro-Meter Việt Nam

Relay card
FEATURES
» From the Vibro-Meter® product line
» Relay card with screw terminal strip
» 16 relays with change-over contacts
» Relay driver inverter logic (jumper selectable)
» Low contact resistance
» Low capacitance
» High through power
» Live insertion and removal of cards (hot-swappable)
» Conforms to EC standards for EMC

DESCRIPTION
The RLC16 relay card is designed for use in the VM600 series of machinery protection systems and condition and performance monitoring systems, from Meggitt Sensing Systems’ Vibro-Meter® product line. It is an optional card, for use when the four relays on the IOC4T input/output card are insufficient for the application and additional relays are required.
The RLC16 is installed in the rear of the VM600 (ABE04x) rack and connects directly to the rack backplane via a single connector.
The RLC16 contains 16 relays with change-over contacts. Each relay is associated with 3 terminals on a screw terminal strip accessible at the rear of the VM600 rack.
The relays are controlled by open-collector drivers under software control. Jumpers on the RLC16 card allow the selection of relay normally energized (NE) or normally de-energized (NDE)

SPECIFICATIONS

Relay characteristics
Relay names : RL1 to RL16
Type : PE014005
Contact arrangement : 1x COM, 1x NC and 1x NO contact/relay.
All relay contacts are available on J1, J2 and J3.
Nominal rated voltage : 250 VAC
Nominal rated current : 5 AAC
Maximum breaking capacity (without contact protection) : 1250 VA

Relay card characteristics
Presentation : 16 relay PCB
Relay state : Normally energized or normally de-energized (jumper selectable)
External connections : Screw terminal connectors (J1, J2 and J3)
Mounting : Installs in the rear of a VM600 rack and connects to the
rack’s backplane via a connector
Temperature range : See above relay characteristics
Humidity : ≤95% (RH non-condensing)
Power supply to RLC16
Supply voltage : +5 VDC
Consumption : 40 mA x16 (per relay)

Environmental
Operating
• Temperature : −25 to +65°C (−13 to +149°F)
• Humidity : 0 to 90% non-condensing
Storage
• Temperature : −40 to +85°C (−40 to +185°F)
• Humidity : 0 to 95% non-condensing
Vibrations and shock : See general VM600 rack specifications Physical
Height : 6U (262 mm, 10.3 in)
Width : 20 mm (0.8 in)
Depth : 125 mm (4.9 in)
Weight : 0.30 kg (0.66 lb)

Ordering number:

200-570-000-1Hh

200-570-000-2Hh

The post VM600 RLC16 relay card Vibro-Meter Việt Nam | Vibro-Meter® Meggitt Việt Nam appeared first on cuahangtudonghoa.com.

Bộ chuyển đổi PA Series Vibro Meter Việt Nam | MEGGITT VIET NAM

cuahangtudonghoa — 2019-05-02 16:59:37

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

Bộ chuyển đổi đầu dò PA150 Vibro Meter

Probe mounting adaptor PA 150

Complete probe mounting adaptor with proximity measurement system (TQ412 and IQS452).

High-quality, high-reliability removable probe housing and probe adaptor rod containing a complete proximity measurement system that consists of a TQ412 proximity sensor and a IQS452 signal conditioner, which provides either a voltage output or a current output (2 mm range: 8 mV/µm or 2.5 µA/µm, 4 mm range: 4 mV/µm or 1.25 µA/µm).

The PA150 is designed and built for long-term use in harsh environments characterised by industrial temperatures and/or hazardous areas (potentially explosive atmospheres).

Features

Removable probe housing and probe adaptor rod containing a complete proximity measurement system (TQ412 and IQS452)
2 or 4 mm measurement range (Ø8.2 mm sensor)
Sealed die-cast aluminium housing and stainless steel adaptor rod, with choice of mounting orientation
Easier probe installation and gap adjustment with adaptor rod lengths from 50 to 800 mm (mounting position adjustable to ±10 mm)
Certified for use in potentially explosive atmospheres

Ordering number: 800 - 150 - 000 - 012

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Output type	Current (2-wire) or voltage (3-wire)
Type of probe mounting adaptor	Removable probe housing and probe adaptor rod
Mounting position adjustment	±0.39 in \| ±10 mm
Probe housing material	Aluminium alloy
Probe housing gasket material	Nitrile rubber (NBR)
Probe adaptor rod material	Stainless steel 1.4301
Probe adaptor assembly material	Stainless steel 1.4305
Mounting orientation for probe housing	Longitudinal or perpendicular
Configurable adaptor length for probe	Yes
Temperature range	−31 to 185 °F \| −35 to 85 °C
Protection rating	IP65
Hazardous area certifications	Ex e

Bộ chuyển đổi gắn đầu dò PA151 Vibro Meter

Probe mounting adaptor PA 151

Removable probe housing and probe adaptor rod.

High-quality, high-reliability removable probe housing and probe adaptor rod to support the external mounting of a TQ412 proximity sensor.

The PA151 is designed and built for long-term use in harsh environments characterised by industrial temperatures and/or hazardous areas (potentially explosive atmospheres).

Features

Removable probe housing and probe adaptor rod to support the external mounting of a TQ412 proximity sensor
Sealed die-cast polyester housing and stainless steel adaptor rod
Easier probe installation and gap adjustment with adaptor rod lengths from 50 to 800 mm (mounting position adjustable to ±10 mm)
−40 to 100 °C temperature, IP65 protection rating
Certified for use in potentially explosive atmospheres

Ordering number: 800 - 151 - 000 - 011

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Type of probe mounting adaptor	Removable probe housing and probe adaptor rod
Mounting position adjustment	±0.39 in \| ±10 mm
Probe housing material	Glass-fibre reinforced polyester
Probe housing gasket material	Neoprene
Probe adaptor rod material	Stainless steel 1.4301
Probe adaptor assembly material	Stainless steel 1.4305
Configurable adaptor length for probe	Yes
Temperature range	−40 to 212 °F \| −40 to 100 °C
Protection rating	IP65
Hazardous area certifications	Ex e

Bộ chuyển đổi đầu dò PA152 Vibro Meter

Probe mounting adaptor PA 152

Probe housing and probe adaptor rod.

High-quality, high-reliability probe housing and probe adaptor rod to support the external mounting of a TQ412 proximity sensor.

The PA152 is designed and built for long-term use in harsh environments characterised by high temperatures.

Features

Probe housing and probe adaptor rod to support the external mounting of a TQ412 proximity sensor
Sealed die-cast aluminium housing and stainless steel adaptor rod
Easier probe installation and gap adjustment with adaptor rod lengths from 50 to 800 mm (mounting position adjustable to ±10 mm)
−40 to 200 °C temperature, IP65 protection rating

Ordering number: 800 - 152 - 000 - 011

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Type of probe mounting adaptor	Probe housing and probe adaptor rod
Mounting position adjustment	±0.39 in \| ±10 mm
Probe housing material	Aluminium alloy
Probe housing gasket material	Silicone
Probe adaptor rod material	Stainless steel 1.4301
Probe adaptor assembly material	Stainless steel 1.4305
Configurable adaptor length for probe	Yes
Temperature range	−40 to 392 °F \| −40 to 200 °C
Protection rating	IP65

Bộ chuyển đổi đầu dò PA153 Vibro Meter

Probe mounting adaptor PA 153

Probe adaptor rod.

High-quality, high-reliability probe adaptor rod to support the external mounting of a TQ412 proximity sensor.

The PA153 is designed and built for long-term use in harsh environments characterised by high temperatures.

Features

Probe adaptor rod to support the external mounting of a TQ412 proximity sensor
Stainless steel adaptor rod
Easier probe installation and gap adjustment with adaptor rod lengths from 50 to 800 mm (mounting position adjustable to ±10 mm)
−40 to 200 °C temperature, IP65 protection rating

Ordering number: 800 - 153 - 000 - 011

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Type of probe mounting adaptor	Probe adaptor rod
Mounting position adjustment	±0.39 in \| ±10 mm
Probe adaptor rod material	Stainless steel 1.4301
Probe adaptor assembly material	Stainless steel 1.4305
Configurable adaptor length for probe	No
Temperature range	−40 to 392 °F \| −40 to 200 °C
Protection rating	IP65

The post Bộ chuyển đổi PA Series Vibro Meter Việt Nam | MEGGITT VIET NAM appeared first on cuahangtudonghoa.com.

Cảm biến tiệm cận TQ Series Vibro-Meter | MEGGITT VIET NAM

cuahangtudonghoa — 2019-05-02 15:42:33

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

TQ401, TQ402, TQ403, TQ412, TQ422, TQ423, TQ432, TQ442

Cảm biến tiệm cận TQ401 Vibro-Meter®

8 mV/µm or 2.5 µA/µm (2 mm range), −40 to 180 °C, Ø5 mm tip, standard-mount.

The TQ401 proximity sensor is a high-quality, high-reliability sensor for use with an EA401 extension cable and IQS450 signal conditioner, which provides either a voltage output or a current output.

The TQ401 is a standard-mount sensor that is designed and built for long-term use in extreme environments characterised by high temperatures and/or hazardous areas (potentially explosive atmospheres).

Features

Designed for the contactless measurement of relative vibration and axial displacement in turbines, compressors, pumps and fans
2 mm measurement range (Ø5 mm sensor)
−40 to 180 °C operating temperature, IP68 protection rating
0.5, 1.0, 1.5, 2.0 or 5.0 m integral coaxial cable
Certified for use in potentially explosive atmospheres

TQ 401 / EA 401 / IQS 450

TQ 401 proximity transducer

Ordering number: 111 - 401 - 000 - 013

EA 401 extension cable

Ordering number: 913 - 401 - 000 - 013

IQS 450 signal conditioner

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Linear measurement range	0.08 in \| 2 mm
Operating temperature range	−40 to 356 °F \| −40 to 180 °C
Sensor (tip) diameter	Ø0.2 in \| Ø5 mm
Mounting options	Standard mount
Integral cable length	1.6, 3.3, 4.9, 6.6 or 16.4 ft \| 0.5, 1.0, 1.5, 2.0 or 5.0 m
Protection rating	IP68
Hazardous area certifications	Ex ia, Ex nA

Cảm biến tiệm cận TQ402 Vibro-Meter®

8 mV/µm or 2.5 µA/µm (2 mm range), 4 mV/µm or 1.25 µA/µm (4 mm range), −40 to 180 °C, Ø8.2 mm tip, standard-mount.

The TQ402 proximity sensor is a high-quality, high-reliability sensor for use with an EA402 extension cable and IQS450 signal conditioner, which provides either a voltage output or a current output.

The TQ402 is a standard-mount sensor that is designed and built for long-term use in extreme environments characterised by high temperatures and/or hazardous areas (potentially explosive atmospheres).

Note: The TQ402 and the TQ412 have the same specifications and performance characteristics but are intended for applications with different installation (mounting) requirements: the TQ402 is a standard-mount sensor and the TQ412 is a reverse-mount sensor.

Features

Designed for the contactless measurement of relative vibration and axial displacement in turbines, compressors, pumps and fans
2 or 4 mm measurement range (Ø8.2 mm sensor)
−40 to 180 °C operating temperature, IP68 protection rating
0.5, 1.0, 1.5, 2.0, 5.0 or 10.0 m integral coaxial cable
Certified for use in potentially explosive atmospheres

TQ 402 and TQ 412 / EA 402 / IQS 450

TQ 402 proximity transducer

Ordering number: 111 - 402 - 000 - 013

TQ 412 proximity transducer

Ordering number: 111 - 412 - 000 - 013

EA 402 extension cable

Ordering number: 913 - 402 - 000 - 013

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Linear measurement range	0.08 or 0.16 in \| 2 or 4 mm
Operating temperature range	−40 to 356 °F \| −40 to 180 °C
Sensor (tip) diameter	Ø0.32 in \| Ø8.2 mm
Mounting options	Standard mount
Integral cable length	1.6, 3.3, 4.9, 6.6, 16.4 or 32.8 ft \| 0.5, 1.0, 1.5, 2.0, 5.0 or 10 m
Protection rating	IP68
Hazardous area certifications	Ex ia, Ex nA

Cảm biến tiệm cận TQ403 Vibro-Meter®

1.33 mV/µm or 0.417 µA/µm (12 mm range), −40 to 180 °C, Ø18 mm tip, standard-mount.

The TQ403 proximity sensor is a high-quality, high-reliability sensor for use with an EA403 extension cable and IQS450 signal conditioner, which provides either a voltage output or a current output.

The TQ403 is a standard-mount sensor that is designed and built for long-term use in extreme environments characterised by high temperatures and/or hazardous areas (potentially explosive atmospheres).

Features

Designed for the contactless measurement of relative vibration and axial displacement in turbines, compressors, pumps and fans
12 mm measurement range (Ø18 mm sensor)
−40 to 180 °C operating temperature, IP68 protection rating
1.0, 5.0 or 10.0 m integral coaxial cable
Certified for use in potentially explosive atmospheres

TQ 403 proximity transducer

Ordering number: 111 - 403 - 000 - 013

EA 403 extension cable

Ordering number: 913 - 403 - 000 - 013

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Linear measurement range	0.47 in \| 12 mm
Operating temperature range	−40 to 356 °F \| −40 to 180 °C
Sensor (tip) diameter	Ø0.71 in \| Ø18 mm
Mounting options	Standard mount
Integral cable length	3.3, 16.4 or 32.8 ft \| 1.0, 5.0 or 10 m
Protection rating	IP68
Hazardous area certifications	Ex ia, Ex nA

Cảm biến tiệm cận TQ412 Vibro-Meter®

8 mV/µm or 2.5 µA/µm (2 mm range), 4 mV/µm or 1.25 µA/µm (4 mm range), −40 to 180 °C, Ø8.2 mm tip, reverse-mount.

The TQ412 proximity sensor is a high-quality, high-reliability sensor for use with an EA402 extension cable and IQS450 signal conditioner, which provides either a voltage output or a current output.

The TQ412 is a reverse-mount sensor that is designed and built for long-term use in extreme environments characterised by high temperatures and/or hazardous areas (potentially explosive atmospheres).

Features

Designed for the contactless measurement of relative vibration and axial displacement in turbines, compressors, pumps and fans
2 or 4 mm measurement range (Ø8.2 mm sensor)
−40 to 180 °C (−40 to 356 °F) operating temperature, IP68 protection rating
0.5, 1.0, 1.5, 2.0, 5.0 or 10.0 m integral coaxial cable
Certified for use in potentially explosive atmospheres

Ordering number: 111 - 412 - 000 - 013

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Linear measurement range	0.08 or 0.16 in \| 2 or 4 mm
Operating temperature range	−40 to 356 °F \| −40 to 180 °C
Sensor (tip) diameter	Ø0.32 in \| Ø8.2 mm
Mounting options	Reverse mount
Integral cable length	1.6, 3.3, 4.9, 6.6, 16.4 or 32.8 ft \| 0.5, 1.0, 1.5, 2.0, 5.0 or 10 m
Protection rating	IP68
Hazardous area certifications	Ex ia, Ex nA

Cảm biến tiệm cận TQ422 Vibro-Meter®

4 mV/µm or 1.25 µA/µm (4 mm range), −25 to 140 °C, Ø12.7 mm tip, standard-mount, 100 bar (tip).

The TQ422 proximity sensor is a high-quality, high-reliability sensor for use with an EA402 extension cable and IQS450 signal conditioner, which provides either a voltage output or a current output.

The TQ422 is a standard-mount, high-pressure sensor that is designed and built for long-term use in extreme environments characterised by high temperatures, high pressures and/or hazardous areas (potentially explosive atmospheres).

Note: The TQ422 and the TQ432 have the same specifications and performance characteristics but are intended for applications with different installation (mounting) requirements: the TQ422 is a standard-mount sensor and the TQ432 is a reverse-mount sensor.

Features

Designed for the contactless measurement of relative vibration and axial displacement in turbines, compressors, pumps and fans
2 or 4 mm measurement range (Ø12.7 mm sensor)
−25 to 140 °C operating temperature, IP68 protection rating, 100 bar pressure rating
1.0, 5.0 or 10.0 m integral coaxial cable
Certified for use in potentially explosive atmospheres

TQ 422 proximity transducer

Ordering number: 111 - 422 - 000 - 013

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Linear measurement range	0.08 or 0.16 in \| 2 or 4 mm
Operating temperature range	−13 to 284 °F \| −25 to 140 °C
Sensor (tip) diameter	Ø0.5 in \| Ø12.7 mm
Mounting options	Standard mount
Integral cable length	3.3, 16.4 or 32.8 ft \| 1.0, 5.0 or 10 m
Pressure	1450 psi \| 100 bar
Protection rating	IP68
Hazardous area certifications	Ex ia, Ex nA

Cảm biến tiệm cận TQ423 Vibro-Meter®

1.33 mV/µm or 0.417 µA/µm (12 mm range), −25 to 140 °C, Ø25 mm tip, standard-mount, 100 bar (tip).

The TQ423 proximity sensor is a high-quality, high-reliability sensor for use with an EA403 extension cable and IQS450 signal conditioner, which provides either a voltage output or a current output.

The TQ423 is a standard-mount, high-pressure sensor that is designed and built for long-term use in extreme environments characterised by high temperatures, high pressures and/or hazardous areas (potentially explosive atmospheres).

Features

Designed for the contactless measurement of relative vibration and axial displacement in turbines, compressors, pumps and fans
12 mm measurement range (Ø25 mm)
−25 to 140 °C operating temperature, IP68 protection rating, 100 bar pressure rating
1.0, 5.0 or 10.0 m integral coaxial cable
Certified for use in potentially explosive atmospheres

TQ 423 proximity transducer

Ordering number: 111 - 423 - 000 - 013

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Linear measurement range	0.47 in \| 12 mm
Operating temperature range	−13 to 284 °F \| −25 to 140 °C
Sensor (tip) diameter	Ø0.98 in \| Ø25 mm
Mounting options	Standard mount
Integral cable length	3.3, 16.4 or 32.8 ft \| 1.0, 5.0 or 10 m
Pressure	1450 psi \| 100 bar
Protection rating	IP68
Hazardous area certifications	Ex ia, Ex nA

Cảm biến tiệm cận TQ432 Vibro-Meter®

4 mV/µm or 1.25 µA/µm (4 mm range), −25 to 140 °C, Ø12.7 mm tip, reverse-mount, 100 bar (tip).

The TQ432 proximity sensor is a high-quality, high-reliability sensor for use with an EA402 extension cable and IQS450 signal conditioner, which provides either a voltage output or a current output.

The TQ432 is a reverse-mount, high-pressure sensor that is designed and built for long-term use in extreme environments characterised by high temperatures, high pressures and/or hazardous areas (potentially explosive atmospheres).

Note: The TQ422 and the TQ432 have the same specifications and performance characteristics but are intended for applications with different installation (mounting) requirements: the TQ422 is a standard-mount sensor and the TQ432 is a reverse-mount sensor.

Features

Designed for the contactless measurement of relative vibration and axial displacement in turbines, compressors, pumps and fans
2 or 4 mm measurement range (Ø12.7 mm sensor)
−25 to 140 °C operating temperature, IP68 protection rating, 100 bar pressure rating
1.0, 5.0 or 10.0 m integral coaxial cable
Certified for use in potentially explosive atmospheres

TQ 432 proximity transducer

Ordering number: 111 - 432 - 000 - 013

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Linear measurement range	0.08 or 0.16 in \| 2 or 4 mm
Operating temperature range	−13 to 284 °F \| −25 to 140 °C
Sensor (tip) diameter	Ø0.5 in \| Ø12.7 mm
Mounting options	Reverse mount
Integral cable length	3.3, 16.4 or 32.8 ft \| 1.0, 5.0 or 10 m
Pressure	1450 psi \| 100 bar
Protection rating	IP68
Hazardous area certifications	Ex ia, Ex nA

Cảm biến tiệm cận TQ442 Vibro-Meter®

8 mV/µm or 2.5 µA/µm (2 mm range), 4 mV/µm or 1.25 µA/µm (4 mm range), −40 to 180 °C, Ø8.2 mm tip, 90°-mount.

The TQ442 proximity sensor is a high-quality, high-reliability sensor for use with an EA402 extension cable and IQS450 signal conditioner, which provides either a voltage output or a current output.

The TQ442 is a 90°-mount sensor that is designed and built for long-term use in extreme environments characterised by high temperatures and/or hazardous areas (potentially explosive atmospheres).

Features

Designed for the contactless measurement of relative vibration and axial displacement in turbines, compressors, pumps and fans
2 or 4 mm measurement range (Ø8 mm sensor)
−40 to 180 °C operating temperature, IP68 protection rating
0.5, 1.0, 1.5, 2.0, 5.0 or 10.0 m integral coaxial cable
Certified for use in potentially explosive atmospheres

TQ 442 proximity transducer

Ordering number: 111 - 442 - 000 - 013

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Linear measurement range	0.08 or 0.16 in \| 2 or 4 mm
Operating temperature range	−40 to 356 °F \| −40 to 180 °C
Sensor (tip) diameter	Ø0.32 in \| Ø8.2 mm
Mounting options	Right-angle (90°) mount
Integral cable length	1.6, 3.3, 4.9, 6.6, 16.4 or 32.8 ft \| 0.5, 1.0, 1.5, 2.0, 5.0 or 10 m
Protection rating	IP68
Hazardous area certifications	Ex ia, Ex nA

The post Cảm biến tiệm cận TQ Series Vibro-Meter | MEGGITT VIET NAM appeared first on cuahangtudonghoa.com.

Bộ điều chỉnh tín hiệu IQS450 - IQS452 Vibro-Meter® | MEGGITT VIET NAM

cuahangtudonghoa — 2019-05-02 15:12:14

Công Ty TNHH TM và DV Tăng Minh Phát là nhà phân phối chính thức của hãng Vibro-Meter® tại Việt Nam.

Bộ điều chỉnh tín hiệu IQS450 - IQS452 Vibro-Meter®

IQS450 signal conditioner

Signal conditioner for use with proximity sensors (TQ).

The IQS450 signal conditioner is a high-quality, high-reliability conditioner for use with the TQ4xx proximity sensors.

The IQS450 is highly configurable (measurement range, sensitivity, total system length), and provides either a current output or a voltage output. It is designed and built for long-term use in environments characterised by hazardous areas (potentially explosive atmospheres).

Features

Signal conditioning for TQ proximity sensors
Very wide frequency range (DC to 20000 Hz)
Configurable transfer function
Current output for signal transmission over long distances or voltage output for signal transmission over medium distances
Certified for use in potentially explosive atmospheres

Ordering number:

204 - 450 - 000 - 002 - A1 - B11 - H05 - I0

204 - 450 - 000 - 002 - A2 - B11 - H05 - I0

204 - 450 - 000 - 002 - A3 - B11 - H05 - I0

204 - 450 - 000 - 002 - A1 - B12 - H05 - I0

204 - 450 - 000 - 002 - A2 - B12 - H05 - I0

204 - 450 - 000 - 002 - A3 - B12 - H05 - I0

204 - 450 - 000 - 002 - A1 - B11 - H10 - I0

204 - 450 - 000 - 002 - A2 - B11 - H10 - I0

204 - 450 - 000 - 002 - A3 - B11 - H10 - I0

204 - 450 - 000 - 002 - A1 - B12 - H10 - I0

204 - 450 - 000 - 002 - A2 - B12 - H10 - I0

204 - 450 - 000 - 002 - A3 - B12 - H10 - I0

204 - 450 - 000 - 002 - A1 - B11 - H05 - I1

204 - 450 - 000 - 002 - A2 - B11 - H05 - I1

204 - 450 - 000 - 002 - A3 - B11 - H05 - I1

204 - 450 - 000 - 002 - A1 - B12 - H05 - I1

204 - 450 - 000 - 002 - A2 - B12 - H05 - I1

204 - 450 - 000 - 002 - A3 - B12 - H05 - I1

204 - 450 - 000 - 002 - A1 - B11 - H10 - I1

204 - 450 - 000 - 002 - A2 - B11 - H10 - I1

204 - 450 - 000 - 002 - A3 - B11 - H10 - I1

204 - 450 - 000 - 002 - A1 - B12 - H10 - I1

204 - 450 - 000 - 002 - A2 - B12 - H10 - I1

204 - 450 - 000 - 002 - A3 - B12 - H10 - I1

204 - 450 - 000 - 002 - A1 - B21 - H01 - I0

204 - 450 - 000 - 002 - A2 - B21 - H01 - I0

204 - 450 - 000 - 002 - A3 - B21 - H01 - I0

204 - 450 - 000 - 002 - A1 - B22 - H01 - I0

204 - 450 - 000 - 002 - A2 - B22 - H01 - I0

204 - 450 - 000 - 002 - A3 - B22 - H01 - I0

204 - 450 - 000 - 002 - A1 - B23 - H01 - I0

204 - 450 - 000 - 002 - A2 - B23 - H01 - I0

204 - 450 - 000 - 002 - A3 - B23 - H01 - I0

204 - 450 - 000 - 002 - A1 - B24 - H01 - I0

204 - 450 - 000 - 002 - A2 - B24 - H01 - I0

204 - 450 - 000 - 002 - A3 - B24 - H01 - I0

204 - 450 - 000 - 002 - A1 - B21 - H05 - I0

204 - 450 - 000 - 002 - A2 - B21 - H05 - I0

204 - 450 - 000 - 002 - A3 - B21 - H05 - I0

204 - 450 - 000 - 002 - A1 - B22 - H05 - I0

204 - 450 - 000 - 002 - A2 - B22 - H05 - I0

204 - 450 - 000 - 002 - A3 - B22 - H05 - I0

204 - 450 - 000 - 002 - A1 - B23 - H05 - I0

204 - 450 - 000 - 002 - A2 - B23 - H05 - I0

204 - 450 - 000 - 002 - A3 - B23 - H05 - I0

204 - 450 - 000 - 002 - A1 - B24 - H05 - I0

204 - 450 - 000 - 002 - A2 - B24 - H05 - I0

204 - 450 - 000 - 002 - A3 - B24 - H05 - I0

204 - 450 - 000 - 002 - A1 - B21 - H10 - I0

204 - 450 - 000 - 002 - A2 - B21 - H10 - I0

204 - 450 - 000 - 002 - A3 - B21 - H10 - I0

204 - 450 - 000 - 002 - A1 - B22 - H10 - I0

204 - 450 - 000 - 002 - A2 - B22 - H10 - I0

204 - 450 - 000 - 002 - A3 - B22 - H10 - I0

204 - 450 - 000 - 002 - A1 - B23 - H10 - I0

204 - 450 - 000 - 002 - A2 - B23 - H10 - I0

204 - 450 - 000 - 002 - A3 - B23 - H10 - I0

204 - 450 - 000 - 002 - A1 - B24 - H10 - I0

204 - 450 - 000 - 002 - A2 - B24 - H10 - I0

204 - 450 - 000 - 002 - A3 - B24 - H10 - I0

204 - 450 - 000 - 002 - A1 - B21 - H01 - I1

204 - 450 - 000 - 002 - A2 - B21 - H01 - I1

204 - 450 - 000 - 002 - A3 - B21 - H01 - I1

204 - 450 - 000 - 002 - A1 - B22 - H01 - I1

204 - 450 - 000 - 002 - A2 - B22 - H01 - I1

204 - 450 - 000 - 002 - A3 - B22 - H01 - I1

204 - 450 - 000 - 002 - A1 - B23 - H01 - I1

204 - 450 - 000 - 002 - A2 - B23 - H01 - I1

204 - 450 - 000 - 002 - A3 - B23 - H01 - I1

204 - 450 - 000 - 002 - A1 - B24 - H01 - I1

204 - 450 - 000 - 002 - A2 - B24 - H01 - I1

204 - 450 - 000 - 002 - A3 - B24 - H01 - I1

204 - 450 - 000 - 002 - A1 - B21 - H05 - I1

204 - 450 - 000 - 002 - A2 - B21 - H05 - I1

204 - 450 - 000 - 002 - A3 - B21 - H05 - I1

204 - 450 - 000 - 002 - A1 - B22 - H05 - I1

204 - 450 - 000 - 002 - A2 - B22 - H05 - I1

204 - 450 - 000 - 002 - A3 - B22 - H05 - I1

204 - 450 - 000 - 002 - A1 - B23 - H05 - I1

204 - 450 - 000 - 002 - A2 - B23 - H05 - I1

204 - 450 - 000 - 002 - A3 - B23 - H05 - I1

204 - 450 - 000 - 002 - A1 - B24 - H05 - I1

204 - 450 - 000 - 002 - A2 - B24 - H05 - I1

204 - 450 - 000 - 002 - A3 - B24 - H05 - I1

204 - 450 - 000 - 002 - A1 - B21 - H10 - I1

204 - 450 - 000 - 002 - A2 - B21 - H10 - I1

204 - 450 - 000 - 002 - A3 - B21 - H10 - I1

204 - 450 - 000 - 002 - A1 - B22 - H10 - I1

204 - 450 - 000 - 002 - A2 - B22 - H10 - I1

204 - 450 - 000 - 002 - A3 - B22 - H10 - I1

204 - 450 - 000 - 002 - A1 - B23 - H10 - I1

204 - 450 - 000 - 002 - A2 - B23 - H10 - I1

204 - 450 - 000 - 002 - A3 - B23 - H10 - I1

204 - 450 - 000 - 002 - A1 - B24 - H10 - I1

204 - 450 - 000 - 002 - A2 - B24 - H10 - I1

204 - 450 - 000 - 002 - A3 - B24 - H10 - I1

204 - 450 - 000 - 002 - A1 - B31 - H05 - I0

204 - 450 - 000 - 002 - A2 - B31 - H05 - I0

204 - 450 - 000 - 002 - A3 - B31 - H05 - I0

204 - 450 - 000 - 002 - A1 - B32 - H05 - I0

204 - 450 - 000 - 002 - A2 - B32 - H05 - I0

204 - 450 - 000 - 002 - A3 - B32 - H05 - I0

204 - 450 - 000 - 002 - A1 - B31 - H10 - I0

204 - 450 - 000 - 002 - A2 - B31 - H10 - I0

204 - 450 - 000 - 002 - A3 - B31 - H10 - I0

204 - 450 - 000 - 002 - A1 - B32 - H10 - I0

204 - 450 - 000 - 002 - A2 - B32 - H10 - I0

204 - 450 - 000 - 002 - A3 - B32 - H10 - I0

204 - 450 - 000 - 002 - A1 - B31 - H05 - I1

204 - 450 - 000 - 002 - A2 - B31 - H05 - I1

204 - 450 - 000 - 002 - A3 - B31 - H05 - I1

204 - 450 - 000 - 002 - A1 - B32 - H05 - I1

204 - 450 - 000 - 002 - A2 - B32 - H05 - I1

204 - 450 - 000 - 002 - A3 - B32 - H05 - I1

204 - 450 - 000 - 002 - A1 - B31 - H10 - I1

204 - 450 - 000 - 002 - A2 - B31 - H10 - I1

204 - 450 - 000 - 002 - A3 - B31 - H10 - I1

204 - 450 - 000 - 002 - A1 - B32 - H10 - I1

204 - 450 - 000 - 002 - A2 - B32 - H10 - I1

204 - 450 - 000 - 002 - A3 - B32 - H10 - I1

Downloads

Specifications

PARAMETER	VALUE (IMPERIAL \| METRIC)
Output type	Current (2-wire) or voltage (3-wire)
Measurement system	TQ proximity
Sensor	TQ proximity sensors
Frequency range	DC to 20000 Hz
Linearity	See performance curves in data sheet
Total measurement system length	3.3, 16.4 and 32.8 ft \| 1, 5 or 10 m
Operating temperature range	−22 to 185 °F \| −30 to 85 °C
Protection rating	IP40
Hazardous area certifications	Ex ia, Ex nA

The post Bộ điều chỉnh tín hiệu IQS450 - IQS452 Vibro-Meter® | MEGGITT VIET NAM appeared first on cuahangtudonghoa.com.

Vibro-Meter® Việt Nam | Đại Lý Phân Phối Vibro-Meter® Việt Nam

Vibro-Meter® Việt Nam

AE119 housing expansion probe | Đầu dò AE 119 Vibro-Meter

Đầu dò AE 119 Vibro-Meter

Pressure sensors (CP) Vibro-Meter | Cảm biến áp suất Vibro-Meter

Cảm biến áp suất Vibro-Meter

Piezoelectric pressure transducer CP 235 | Cảm biến đo áp suất CP 235

2. Pressure transducer CP216 | Đầu dò áp suất CP216

3. Pressure transducer CP 103 | Đầu dò áp suất CP 103

Vibration sensors Meggitt | Cảm biến rung Vibro-Meter

Cảm biến rung Vibro-Meter

Vibration sensors (CA, CE, CV, PV, SE and VE)

Velocity transducer CV213/CV214 | Đầu dò vận tốc CV213/CV214 Vibro-Meter

Velocity transducer CV213/CV214

Relay card Vibro-Meter® | Đại Lý Phân Phối Vibro-Meter® tại Việt Nam

Vibro-Meter® Việt Nam

Bộ nguồn 200-582-500-021 RPS6U - Vibro Meter Việt Nam | MEGGITT VIET NAM

NEGGITT VIET NAM

19\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\" Rack Types ABE 040 & ABE 042 Vibro-Meter® Việt Nam | MEGGITT VIET NAM

620-005-0Ss-1Hh Relay Card Vibro Meter Việt Nam | MEGGITT VIET NAM

AMC8 and IOC8T Mạch bảo vệ Vibro Meter | MEGGITT VIET NAM

CPUM and IOCN Bảng Mạch Vibro Meter | MEGGITT VIET NAM

Bo Mạch VM600 MPC4 Vibro-Meter | Vibro-Meter® Meggitt

VM600 RLC16 relay card Vibro-Meter Việt Nam | Vibro-Meter® Meggitt Việt Nam

Bộ chuyển đổi PA Series Vibro Meter Việt Nam | MEGGITT VIET NAM

Cảm biến tiệm cận TQ Series Vibro-Meter | MEGGITT VIET NAM

Bộ điều chỉnh tín hiệu IQS450 - IQS452 Vibro-Meter® | MEGGITT VIET NAM

Downloads